SUBJECTS
|
BROWSE
|
CAREER CENTER
|
POPULAR
|
JOIN
|
LOGIN
Business Skills
|
Soft Skills
|
Basic Literacy
|
Certifications
About
|
Help
|
Privacy
|
Terms
|
Email
Search
Test your basic knowledge |
Engineering Graphics And Design
Start Test
Study First
Subject
:
engineering
Instructions:
Answer 50 questions in 15 minutes.
If you are not ready to take this test, you can
study here
.
Match each statement with the correct term.
Don't refresh. All questions and answers are randomly picked and ordered every time you load a test.
This is a study tool. The 3 wrong answers for each question are randomly chosen from answers to other questions. So, you might find at times the answers obvious, but you will see it re-enforces your understanding as you take the test each time.
1. A ___ is a cylindrical or spherical surface or a set of two opposed elements or opposed parallel surfaces associated with a size dimension
Locational interference fit
Diameters
Feature with size
Bilateral equal
2. in some ways - symmetry and concentricity are very similar. The main difference is that the former is typically concerned with the position of a center plane relative to an axis or a center plane of a datum feature.
Form
Symmetry
Feature cotnrol
Interferance
3. The counterpart of MMC is the ___ - which is the condition in which a feature of size contains the minimum amount of material within the stated limits of size
Least material condition
Counter bore
Tolerance
Arrow head
4. ___ is a fit where the two mating parts have intersecting nominal volumes - requiring the deformation of the parts
Interferance
Direct
Locational interference fit
Profile
5. when the inside dimensions are more important or more critical than the overall dimension - the overall dimension should be identified as a ___ dimension
Bilateral equal
Reference
Feature with size
Extension line
6. In GD&T - ___ of a surface specifies a 3D tolerance zone defined by two contoured surfaces. When a datum reference is not specified - the tolerance controls only the shape of the contour. When datums are specified - the tolerance controls the shape o
Millimeter
Least material condition
20
Profile
7. Datums are not allowed for v
Cylindricity
Geometric
Non rigid
Least material condition
8. Arcs are dimensioned as radii using the ___ symbol - which is shown preceding the dimension value.
Datum
Tolerance
R
Ansi y14.5
9. ___ is a 2D control similar to circulatirty or roundness. the main difference is that it controls a surface relative to a datum axis.
Circular runout
Profile
Cylindricity
20
10. Which type of english fit is inteded where accuracy of location is of prime importance and where parts require rigidity and alignment with no special requirement for bore pressure?
Position
Tolerance
Baseline
Locational interference fit
11. Each dimension shall have a ___ - except for those dimensions specifically identified as reference - maximum - minimum - or stock
Arrow head
Tolerance
Features without size
Bilateral
12. A small triangle at the end of a dimension liens and leaders that indicates the direction and extent of a dimension is called a ___
Arrow head
Dimension
Profile
Gothic
13. Engineering drawings require the use of single stroke ___ lettering
The order that a machinist would perform the operations
Countersunk
Gothic
Circular runout
14. Datums are always required for ___
Baseline
Tolerance
Bilateral equal
Position
15. ___ refers to a fit where there is space between the two mating parts.
Reference
Chamfers
Clearance
Dimension
16. In ___ dimensioning - all of the dimensions in a given direction originate from a base or datum
Force fit
Interferance
Geometric
Baseline
17. A good analogy of the ___ control is a stack of pennies. this tolerance would control how round each penny is but not the straightness of the whole stack
Circular runout
Ten
Circularity
Clearance
18. A ___ is typically a planar surface or a feature where the normal vectors point in the same direction
Chain
Features without size
The order that a machinist would perform the operations
Tolerance
19. ___ dimensioning usually yields the largest accumulation of tolerance between features.
Chain
Transition
Non rigid
Counter bore
20. ___ tolerances are tolerances where the deviation is divided in some way above and below the basic size of the dimension.
General
Cylindricity
Diameters
Bilateral
21. ___ are used to direct a dimension - note - or symbol to the intended place on a drawing.
Rectangular
Cylindricity
Leaders
Gothic
22. A good rule of thumb to follow when dimensioning is to dimension only visible or ___ lines
Reference
Direct
Solid
Circular runout
23. Which type of metric fit is suitable for parts that can be highly stressed or for shrink fits where the heavy pressure forces required are impractical?
Interferance
Force fit
Solid
Countersunk
24. ___ are beveled or angled edges that typically appear on the ends of shafts or fasteners. They are dimensioned by giving a length from the end of the part and an angle or by specifying two distances
Chamfers
Tolerance
R
Tolerance
25. Most drawings conform to the International System of Units (SI) which is metric and uses the ____ as the standard unit; or they conform to US customary unites with standard unit of the decimal inch
Millimeter
Circular runout
Position
Dimension
26. For machined parts - the amount of variation - or ___ - might be relatively small
Countersunk
Tolerance
Chain
Counter bore
27. In DG&T - the ___ reference frame is a theoretical system made up of three mutually perpendicular planes established by real features on the object.
Ansi y14.5
Datum
Extension line
Symmetry
28. A __ line - along with its arrowheads - shows the direction and extent of a dimension
Profile
Force fit
Features without size
Dimension
29. ___ tolerances are for individual features and are not related to any datums. This group of geometric tolerances includes straightness - flatness - circularity - and cylindricity
Circular runout
Form
Clearance
Direct
30. ___ notes typically appear in the lower right hand corner of a drawing and apply to the whole drawing
The order that a machinist would perform the operations
General
Tolerance
Symmetry
31. There are standards for specifying particular types of geometry. for example - circles are typically dimensioned as ___ - and arcs are dimensioned as radii
Diameters
Chain
Position
Cylindricity
32. Unless otherwise specified - all dimensions are applicable at ___ degrees celsius. compensation may be made for measurements made at other temperatures..
Geometric
Chamfers
20
Datum
33. In ___ dimensioning - features are dimensioned relative to one another
Chain
R
Millimeter
Ansi y14.5
34. Baseline dimension is often used for CNC machines that work from a ___ coordinate system
Chain
Rectangular
Tolerance
Maximum material condition
35. When you dimension holes - you string the symbols together in ___
The order that a machinist would perform the operations
Non rigid
Geometric
Solid
36. The main focus of GD&T is the ___ frame which contains the geometric characteristic symbol - the geometric tolerance - and the relative datums.
Extension line
Non rigid
Chamfers
Feature cotnrol
37. ___ is the difference between the maximum material limits of mating parts
General
Tolerance
Profile
Allowance
38. All datum simulators must be at least ___ times better in quality than the tolerances specified on the drawings to be considered datum simulators
Ten
Geometric
Allowance
Interferance
39. In GD&T - the ___ (MMC) modifier allows the size of the zone to change if the size of the hole changes
Bilateral
Maximum material condition
General
Datum
40. Dimension lines als should be at least ___ millimeters from any view - helping to avoid clutter
Cylindricity
Countersunk
Position
Ten
41. The accepted national standard in the united states for dimension and tolerancing is...
Bilateral
Ansi y14.5
Tolerance
Clearance
42. ___ holes are used for applications with flat head and oval head screws
Form
Features without size
Countersunk
Profile
43. When profile tolerances are equally distributed about the perfect geometry of the features - this is referred to as a ___ distribution.
Bilateral equal
Millimeter
Ten
Feature cotnrol
44. A thin - dark - solid lien extending from a point on an object and perpendicular to a dimension line is called an ___
Geometric
Ten
Extension line
Cylindricity
45. A numerical value expressed in appropriate units of measure and used to define the size - location - geometric characteristic - - or surface texture of a aprt or part feature is a ___
Leaders
Chain
Dimension
Bilateral equal
46. ___ holes are standard machined holes that are used to accept fillister head and hex sockets head screws
Counter bore
Transition
Dimension
Leaders
47. ___ fits are typically associated with selective assembly
Transition
Tolerance
Circular runout
Least material condition
48. All dimensions and tolerances apply in a free state condition. this principle does not apply to ___ parts
Least material condition
Non rigid
The order that a machinist would perform the operations
20
49. Which type of dimensiong offers the best way to eliminate toelrance accumulation?
Ansi y14.5
Bilateral equal
Position
Direct
50. ___ dimensioning an tolerancing is a 4d mathematical system that allows a designer to describe the form - orientation - and location of features on a part within precise tolerance zones.
Extension line
Geometric
Transition
Bilateral equal