SUBJECTS
|
BROWSE
|
CAREER CENTER
|
POPULAR
|
JOIN
|
LOGIN
Business Skills
|
Soft Skills
|
Basic Literacy
|
Certifications
About
|
Help
|
Privacy
|
Terms
|
Email
Search
Test your basic knowledge |
NATE Air Conditioning Components
Start Test
Study First
Subjects
:
engineering
,
nate
Instructions:
Answer 50 questions in 15 minutes.
If you are not ready to take this test, you can
study here
.
Match each statement with the correct term.
Don't refresh. All questions and answers are randomly picked and ordered every time you load a test.
This is a study tool. The 3 wrong answers for each question are randomly chosen from answers to other questions. So, you might find at times the answers obvious, but you will see it re-enforces your understanding as you take the test each time.
1. Before energizing a newly installed system - what test should always be done...
The suction line must be pitched toward the condensing unit
Compressor
A compression fitting
Check for tight connections at electrical terminals
2. In a sealed system - as the pressure increases...
208-volt/240-volt single-phase power supply
The cooling contactor coil
Refrigerant must be added to the system
The temperature increases
3. What is the 'W' terminal used for on the thermostat...
The heating control circuit
The contactor coil
Check for tight connections at electrical terminals
Condenser
4. What must be done to the system when a condensing unit is precharged for 25' of refrigerant line and uses 32' of refrigerant line...
The heating control circuit
208-volt/240-volt single-phase power supply
A TXV
Refrigerant must be added to the system
5. In a sealed system - as the pressure increases...
Capillary action
The blower relay coil
The temperature increases
The suction line must be pitched toward the condensing unit
6. What is the 'Y' terminal used for on the thermostat...
The power from the transformer
Evaporator
The cooling contactor coil
The accumulator
7. Why is it recommended to add a gravel fill under the pad of a condensing unit...
Metering device (restrictor)
This will prevent settling of the ground - which can cause refrigerant line damage
The accumulator
Evaporator
8. Which part of the system stores refrigerant until it is needed in the evaporator...
The suction line must be pitched toward the condensing unit
The compressor and condenser connected by a refrigeration line set to the metering device and evaporator
The receiver
24 volts
9. The part of an air conditioning system that changes the refrigerant from a high-pressure liquid to a low-pressure liquid is the...
Have a minimum perimeter of 3' larger than the unit being served
Metering device (restrictor)
Metering device
The power from the transformer
10. An auxiliary drain pan must...
11. The part of an air conditioning system that changes the refrigerant from a high-pressure gas to a high-pressure liquid is the...
Have a minimum perimeter of 3' larger than the unit being served
The temperature increases
Condenser
The receiver
12. The part of an air conditioning system that changes the refrigerant from a low-pressure liquid to a low-pressure gas is the...
208-volt/240-volt single-phase power supply
24 volts
Evaporator
This will prevent settling of the ground - which can cause refrigerant line damage
13. When installing an evaporator coil - before soldering - the end of the evaporator lines must be opened to the atmosphere because...
The coil is precharged with nitrogen
Compressor
The receiver
This will prevent settling of the ground - which can cause refrigerant line damage
14. When installing a refrigeration line set through a masonry wall
The lines must be covered by PVC to prevent contact with the masonry material
Near a return-air grill
Have a minimum perimeter of 3' larger than the unit being served
208-volt/240-volt single-phase power supply
15. When soldering a copper connection and solder is drawn into the joint - This is commonly called...
The cooling contactor coil
The contactor coil
Capillary action
A TXV
16. When installing a refrigeration line set through a masonry wall
The lines must be covered by PVC to prevent contact with the masonry material
The power from the transformer
Compressor
Compressor
17. What is the 'are' terminal used for on the thermostat...
The power from the transformer
Metering device
A TXV
Refrigerant must be added to the system
18. Which part of the system prevents liquid from entering the compressor...
Condenser
The accumulator
24 volts
Metering device (restrictor)
19. To ensure proper oil return to the compressor - a coiled refrigeration lineset...
Must be coiled horizontally and the vapor must flow from top to bottom
Insulated
Near a return-air grill
Evaporator
20. What type of metering device is used on a 12 SEER split air conditioning system...
The heating control circuit
Must be located in a conspicuous place to serve as an alarm
A TXV
Insulated
21. Residential split-system outdoor condensing units are commonly wired with a...
The contactor coil
The power from the transformer
208-volt/240-volt single-phase power supply
The temperature increases
22. What is the purpose for insulating a suction line...
Must be coiled horizontally and the vapor must flow from top to bottom
To prevent condensation from forming
Evaporator
Check for tight connections at electrical terminals
23. A normally closed float switch that is connected to an auxiliary drain pan should be wired to control...
Have a minimum perimeter of 3' larger than the unit being served
Metering device
The contactor coil
The power from the transformer
24. What is the 'G' terminal used for on the thermostat...
The blower relay coil
The power from the transformer
Condenser
A TXV
25. What is the 'W' terminal used for on the thermostat...
The heating control circuit
This will prevent settling of the ground - which can cause refrigerant line damage
Have a minimum perimeter of 3' larger than the unit being served
The lines must be covered by PVC to prevent contact with the masonry material
26. Where does the refrigerant change from a high-pressure liquid to a low-pressure liquid...
24 volts
The receiver
Check for tight connections at electrical terminals
Metering device (restrictor)
27. Which part of the system stores refrigerant until it is needed in the evaporator...
The accumulator
The cooling contactor coil
The receiver
The coil is precharged with nitrogen
28. What is the 'G' terminal used for on the thermostat...
Evaporator
Must be located in a conspicuous place to serve as an alarm
A TXV
The blower relay coil
29. Which part of the system prevents liquid from entering the compressor...
The accumulator
Check for tight connections at electrical terminals
The contactor coil
Metering device (restrictor)
30. Quick-connect fittings are commonly used on...
The accumulator
Precharged refrigeration linesets
Metering device
A compression fitting
31. What is the 'are' terminal used for on the thermostat...
The power from the transformer
The blower relay coil
The compressor and condenser connected by a refrigeration line set to the metering device and evaporator
A compression fitting
32. A secondary drain line...
The power from the transformer
Metering device (restrictor)
Must be located in a conspicuous place to serve as an alarm
The heating control circuit
33. The part of an air conditioning system that changes the refrigerant from a high-pressure liquid to a low-pressure liquid is the...
Metering device
24 volts
Condenser
The blower relay coil
34. Where does the refrigerant change from a high-pressure liquid to a low-pressure liquid...
Metering device (restrictor)
Check for tight connections at electrical terminals
The compressor and condenser connected by a refrigeration line set to the metering device and evaporator
Must be located in a conspicuous place to serve as an alarm
35. Where does the refrigerant change from a low-pressure liquid to a low-pressure gas...
The cooling contactor coil
Have a minimum perimeter of 3' larger than the unit being served
Check for tight connections at electrical terminals
Evaporator
36. A normally closed float switch that is connected to an auxiliary drain pan should be wired to control...
The coil is precharged with nitrogen
The contactor coil
Must be coiled horizontally and the vapor must flow from top to bottom
Check for tight connections at electrical terminals
37. The part of an air conditioning system that changes the refrigerant from a low-pressure gas to a high-pressure gas is the...
Capillary action
To prevent condensation from forming
Insulated
Compressor
38. An auxiliary drain pan must...
39. The part of an air conditioning system that changes the refrigerant from a high-pressure gas to a high-pressure liquid is the...
A compression fitting
The accumulator
This will prevent settling of the ground - which can cause refrigerant line damage
Condenser
40. A split-system air conditioning unit has...
Must be located in a conspicuous place to serve as an alarm
Compressor
The lines must be covered by PVC to prevent contact with the masonry material
The compressor and condenser connected by a refrigeration line set to the metering device and evaporator
41. If ductwork is located in an attic or crawl space - it must be...
Compressor
Check for tight connections at electrical terminals
Insulated
The blower relay coil
42. A room thermostat should be mounted...
The suction line must be pitched toward the condensing unit
Metering device (restrictor)
Near a return-air grill
The suction line must be pitched toward the condensing unit
43. The part of an air conditioning system that changes the refrigerant from a low-pressure liquid to a low-pressure gas is the...
Evaporator
The blower relay coil
24 volts
Metering device (restrictor)
44. Where does the refrigerant change from a low-pressure liquid to a low-pressure gas...
The power from the transformer
Evaporator
Check for tight connections at electrical terminals
This will prevent settling of the ground - which can cause refrigerant line damage
45. What is the secondary voltage on a step-down control transformer for a residential furnace...
24 volts
The coil is precharged with nitrogen
This will prevent settling of the ground - which can cause refrigerant line damage
Evaporator
46. To ensure proper oil return to the compressor - a coiled refrigeration lineset...
Insulated
The coil is precharged with nitrogen
Metering device (restrictor)
Must be coiled horizontally and the vapor must flow from top to bottom
47. Where does the refrigerant change from a low-pressure gas to a high-pressure gas...
Compressor
Insulated
The suction line must be pitched toward the condensing unit
The compressor and condenser connected by a refrigeration line set to the metering device and evaporator
48. What type of fitting uses an O-ring to help seal its joint...
A compression fitting
Refrigerant must be added to the system
Insulated
The receiver
49. What must be done to the system when a condensing unit is precharged for 25' of refrigerant line and uses 32' of refrigerant line...
Refrigerant must be added to the system
The contactor coil
Evaporator
The blower relay coil
50. Where does the refrigerant change from a high-pressure gas to a high-pressure liquid...
A compression fitting
Condenser
208-volt/240-volt single-phase power supply
Must be coiled horizontally and the vapor must flow from top to bottom